View 74F51_1123715.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
74F51 Dual 2-wide 2-input, 2-wise 3-input AND-OR-invert gate
Product specification IC15 Data Handbook 1989 Mar 03
Philips Semiconductors
Philips Semiconductors
Product specification
Dual 2-wide 2-input, 2-wide 3-input AND-OR-invert gate
74F51
TYPE 74F51
TYPICAL PROPAGATION DELAY 3.0ns
TYPICAL SUPPLY CURRENT (TOTAL) 3.5mA
PIN CONFIGURATION
D0a D1a D1b 1 2 3 4 5 6 7 14 13 12 11 10 9 8 VCC D0c D0b D0f D0e D0d Q0
ORDERING INFORMATION
DESCRIPTION 14-pin plastic DIP 14-pin plastic SO COMMERCIAL RANGE VCC = 5V 10%, Tamb = 0C to +70C N74F51N N74F51D PKG DWG # SOT27-1 SOT108-1
D1c D1d Q1 GND
SF00085
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
PINS DESCRIPTION 74F (U.L.) HIGH/LOW Dna, Dnb, Dnc, Dnd, Dne, Dnf Data inputs 1.0/1.0 Q0, Q1 Data outputs 50/33 NOTE: One (1.0) FAST unit load is defined as: 20A in the High state and 0.6mA in the Low state. LOAD VALUE HIGH/LOW 20A/0.6mA 1.0mA/20mA
LOGIC SYMBOL
IEC/IEEE SYMBOL
9
&
1
1
12
13
9
10
11
2
3
4
5
10 11 8 13
D0a D0b D0c D0d D0e D0f D1a D1b D1c D1d 12 1 Q0 Q1 2 3 8 VCC = Pin 14 GND = Pin 7 6 4 5
&
& &
1
6
SF00086
SF00087
LOGIC DIAGRAM
D0a D0b D0c D0d D0e D0f 1 12 13 8 9 10 11 Q0
FUNCTION TABLE FOR 3-INPUT GATES
D0a H X D0b H X INPUTS D0c D0d D0e H X X X H H All other combinations D0f X H OUTPUT Q0 L L H
D1a D1b D1c D1d VCC = Pin 14 GND = Pin 7
2 3 6 4 5 Q1
NOTES: H = High voltage level L = Low voltage level X = Don't care
FUNCTION TABLE FOR 2-INPUT GATES
INPUTS D1a D1b H X D1c X H D1d X H H X OUTPUT Q1 L L H
SF00088
All other combinations NOTES: H = High voltage level L = Low voltage level X = Don't care
March 3, 1989
2
853-0054 95962
Philips Semiconductors
Product specification
Dual 2-wide 2-input, 2-wide 3-input AND-OR-invert gate
74F51
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL VCC VIN IIN VOUT IOUT Tamb Tstg Supply voltage Input voltage Input current Voltage applied to output in High output state Current applied to output in Low output state Operating free-air temperature range Storage temperature range PARAMETER RATING -0.5 to +7.0 -0.5 to +7.0 -30 to +5 -0.5 to VCC 40 0 to +70 -65 to +150 UNIT V V mA V mA C C
RECOMMENDED OPERATING CONDITIONS
LIMITS SYMBOL VCC VIH VIL IIK IOH IOL Tamb Supply voltage High-level input voltage Low-level input voltage Input clamp current High-level output current Low-level output current Operating free-air temperature range 0 PARAMETER MIN 4.5 2.0 0.8 -18 -1 20 +70 NOM 5.0 MAX 5.5 V V V mA mA mA C UNIT
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST CONDITIONS1 VCC = MIN, VIL = MAX VIH = MIN, IOH = MAX Low-level Low level output voltage Input clamp voltage Input current at maximum input voltage High-level input current Low-level input current Short-circuit output current3 Supply current (total) ICCH VCC = MIN, VIL = MAX VIH = MIN, IOL = MAX VCC = MIN, II = IIK VCC = MAX, VI = 7.0V VCC = MAX, VI = 2.7V VCC = MAX, VI = 0.5V VCC = MAX VCC = MAX VIN = GND -60 1.8 10%VCC 5%VCC 10%VCC 5%VCC LIMITS MIN 2.5 2.7 3.4 0.30 0.30 -0.73 0.50 0.50 -1.2 100 20 -0.6 -150 3.0 TYP2 MAX UNIT V V V V V A A mA mA mA
VO OH
High level output voltage High-level
VO OL VIK II IIH IIL IOS ICC
ICCL VIN = 4.5V 5.5 7.5 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25C. 3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last.
March 3, 1989
3
Philips Semiconductors
Product specification
Dual 2-wide 2-input, 2-wide 3-input AND-OR-invert gate
74F51
AC ELECTRICAL CHARACTERISTICS
LIMITS SYMBOL PARAMETER TEST CONDITION VCC = +5.0V Tamb = +25C CL = 50pF, RL = 500 MIN tPLH tPHL Propagation delay Dna, Dnb, Dnc, Dnd, Dne, Dnf to Qn Waveform 1 2.0 1.0 TYP 3.5 2.5 MAX 5.5 4.0 VCC = +5.0V 10% Tamb = 0C to +70C CL = 50pF, RL = 500 MIN 1.5 1.0 MAX 6.5 4.5 ns UNIT
AC WAVEFORMS
Dna, Dnb, Dnc, Dnd, Dne, Dnf
VM tPHL
VM tPLH
Qn
VM
VM
SF00089
Waveform 1. Propagation Delay for Inverting Outputs NOTE: For all waveforms, VM = 1.5V.
TEST CIRCUIT AND WAVEFORM
VCC NEGATIVE PULSE VIN PULSE GENERATOR RT D.U.T. VOUT 90% VM 10% tTHL (tf ) CL RL tw VM 10% tTLH (tr ) 0V 90% AMP (V)
tTLH (tr ) 90% POSITIVE PULSE VM 10% tw
tTHL (tf ) AMP (V) 90% VM 10% 0V
Test Circuit for Totem-Pole Outputs DEFINITIONS: RL = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. CL = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. RT = Termination resistance should be equal to ZOUT of pulse generators.
Input Pulse Definition INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0V 1.5V rep. rate 1MHz tw 500ns tTLH 2.5ns tTHL 2.5ns
SF00006
March 3, 1989
4
Philips Semiconductors
Product specification
Dual 2-wide 2-input, 2-wise 3-input AND-OR-invert gate
74F51
DIP14: plastic dual in-line package; 14 leads (300 mil)
SOT27-1
1989 Mar 03
5
Philips Semiconductors
Product specification
Dual 2-wide 2-input, 2-wise 3-input AND-OR-invert gate
74F51
SO14: plastic small outline package; 14 leads; body width 3.9 mm
SOT108-1
1989 Mar 03
6
Philips Semiconductors
Product specification
Dual 2-wide 2-input, 2-wise 3-input AND-OR-invert gate
74F51
NOTES
1989 Mar 03
7
Philips Semiconductors
Product specification
Dual 2-wide 2-input, 2-wise 3-input AND-OR-invert gate
74F51
Data sheet status
Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product.
Production
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Disclaimers
Life support -- These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 (c) Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. print code Document order number: Date of release: 10-98 9397-750-05065
Philips Semiconductors
yyyy mmm dd 8

▲Up To Search▲

Price & Availability of 74F51

	To Download 74F51 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .